'Flexo Press'에 해당되는 글 2건

The F5 flexographic press is a highly automated, multi-substrate flexographic press that is capable of printing up to 12 colors, and is designed for printing and post processing of various labels, including films, shrink sleeves, wrap-around labels, sheets of hoses, adhesive label and flexible packaging materials.

* Quick changeover without tooling

* Hot air or UV drying
* UV rotary screen
* Pr-registration and auto-registration
* Rail system for portable coil foil/screen,ect
* Turn bar,Delam/relam,Diecutting,Sheeting & Laminating cold foil etc.
* Chilled drum is option
* Record the data of different material
* Air cylinder locked ink tray,Separated Anilox with ink pan

Speed -> 150m/min 
Web width -> 330/430mm 
Repeat length -> 229mm-502 mm 
Max.Unwind diameter -> 760 and/or 1000 mm 
rewind diameter -> 760 and/or 1000 mm 
Max.Units -> 12 
UV curing power  -> 400 w/inch 

--------------------------------------------------------------------------------------
* Features introduction:
1. Servo drive
Built-in dual servo driven system offers more capabilities, including an automatic alignment, automatic registration and secondary registration, makes the operation much easier, stable and eliminates bar marking effectively.

2. Short web path design
Short web path design for only 1.3 meter within a printing station can reduce material waste during start up and printing job change. Paper path reduced to 15 meters because flexo printing press equipped with eight colors printing plus two die stations. 

3. Lock ink cassette by air cylinder
Lock ink cassette by air cylinder, Which makes operation easier and more quickly change. Separated Anilox with in pan, as well as avoids the removal of the anilox roll when changing the ink.

4. Pre-registration and auto-registration
F5 flexo printing press includes Pre-registration and auto-registration which improves both efficiency and cost savings.

5. Nip device on waste rewind
Nip device on waste rewind to guarantee waste matrix to be unbreakable during high speed production which increases effectiveness and yield of production since we can push matrix width to the minimum required by the cutting edge of knife. 

6. Movable rail
Movable rail makes the flexo press earier extend more options, including a delam/relam device, UV rotary screen, turn bar, die cut, screen print, laminating and cold foil.

7. Advanced tension control device
With an advanced tension control device, the lables on 12 micron film, sticker and paper board can all be printed using the F5 flexo printing press. Change of operating speed will not affect registration. There is no waste during jogging and all the way up to production speed. 

8. Drying
Drying options include hot air and UV drying (or LED UV). UV drying equipment is from Europe, and self-designed hot air drying enables solid printing to be dried at 40℃ at 150 m/min 

9. The control system can record and recall process parameters of different materials.

10. The water cooled UV curing system, ensures materials maintain a suitable temperature when UV drying, and is suitable for the processing of thermal deformation materials.

11. It is equipped with an internet access function so that all devices can be remotely maintained and upgraded.

The entire operation is humanized due to the above mentioned technologies. Operator can easily run the equipment.Plates change for each order only takes 20 to 30 minutes. Substrate waste during start up is around 30 to50 meters. The waste during web change can be controlled within10 meters. It is a piece of equipment suitable for short and midsize run. Actual production speed can be easily reached up to 100-120 meters/min. It fits for long run job as well.

* Specification

Speed -> 150m/min
Web width -> 330/430 mm
Repeat length -> 229mm-502 mm
Max.unwind diameter -> 760 and/or 1200 mm
Max.rewind diameter -> 760 and/or 1200 mm
Max.units -> 12
UV curing power -> 400 w/inch

-------------------------------------------------------------------------------------
* Features introduction

The entire operation is humanized due to the above mentioned technologies. Operator can easily run the equipment.Plates change for each order only takes 20 to 30 minutes. Substrate waste during start up is around 30 to50 meters. The waste during web change can be controlled within10 meters. It is a piece of equipment suitable for short and midsize run. Actual production speed can be easily reached up to 100-120 meters/min. It fits for long run job as well.

1. Servo drive
Built-in full servo driven system offers more capabilities which makes the operation much easier, stable and eliminates bar marking effectively.

2. Short web path design
Short web path design for only 1.3 meter within a printing station can reduce material waste during start up and printing job change .Because total footage of a system equipped with eight colors printing plus two die stations is less than 15 meters.

3. Pre-registration and pre-pressure setting
Pre-registration and Pre-determined pressure mechanism will maintain anilox pressure and impression pressure after plate cylinder changed to shorten the time of jogging and reduce substrate waste

4. Nip device on waste rewind
Nip device on waste rewind to guarantee waste matrix to be unbreakable during high speed production which increases effectiveness and yield of production since we can push matrix width to the minimum required by the cutting edge of knife.

5. Advanced tension control device
With an advanced tension control device, the lables on 12 micron film, sticker and paper board can all be printed using the F5 flexo printing press. Change of operating speed will not affect registration. There is no waste during jogging and all the way up to production speed.

6. Movable rail
Movable rail makes the flexo press earier extend more options, including a delam/relam device, UV rotary screen, turn bar, die cut, screen print, laminating and cold foil.

7. Lock ink cassette by air cylinder
Lock ink cassette by air cylinder, Which makes operation easier and more quickly change. Separated Anilox with in pan, as well as avoids the removal of the anilox roll when changing the ink.

8. Drying
Drying options include hot air and UV drying (or LED UV). UV drying equipment is from Europe, and self-designed hot air drying enables solid printing to be dried at 40℃ at 150 m/min.

9. The control system can record and recall process parameters of different materials.

10.The water cooled UV curing system, ensures materials maintain a suitable temperature when UV drying, and is suitable for the processing of thermal deformation materials.

11. It is equipped with an internet access function so that all devices can be remotely maintained and upgraded.